Universal Controller provides native support of Modbus protocol for Modbus physical interfaces (PHIs). Core support is provided with pymodbus Python module, but with additional functionality, such as bus locking, automatic retry attempts, virtual ports for drivers etc.
Universal Controller works as Modbus master, connection links to all slave devices should be defined as virtual ports. After that, defined virtual ports and Modbus unit IDs should be set in corresponding PHI modules load configurations.
Defining Modbus virtual port
Before using any Modbus PHI, you must define Modbus virtual port. Modbus PHIs work with Modbus virtual ports only, while UC handles all hardware calls and responses.
List of the defined Modbus virtual ports can be obtained with command:
eva uc modbus list
To create new Modbus virtual port, execute the following command:
eva uc modbus create [-l] [-t SEC] [-r RETRIES] [-d SEC] [-y] ID PARAMS
- -l lock port on operations, which means to wait while Modbus port is used by another controller thread (driver command)
- -t SEC Modbus operations timeout (in seconds, default: default timeout)
- -r RETRIES retry attempts for each operation (default: no retries)
- -d SEC delay between virtual port operations (default: 20ms)
- -y save Modbus port config after creation
- ID virtual port ID which will be used later in PHI configurations
- PARAMS Modbus params
Modbus params should contain the configuration of hardware Modbus port. The following hardware port types are supported:
- tcp , udp Modbus protocol implementations for TCP/IP networks. The params should be specified as: <protocol>:<host>[:port], e.g. tcp:192.168.11.11:502
- rtu, ascii, binary Modbus protocol implementations for the local bus connected with USB or serial port. The params should be specified as: <protocol>:<device>:<speed>:<data>:<parity>:<stop> e.g. rtu:/dev/ttyS0:9600:8:E:1
As soon as the port is created, it can be used by PHI. Let’s create Modbus TCP port and load dae_ro16_modbus PHI module:
eva uc modbus create p1 tcp:192.168.11.11:502 -y eva uc phi load r1 dae_ro16_modbus -c port=p1,unit=1 -y
UC will grant Modbus port access to PHI only if it has enough timeout to wait for the longest possible call. It means operation timeout (action_timeout, update_timeout) in item should be greater than modbus_port_timeout*(1+modbus_port_retries). If the command max timeout is less than this value, attempts to access Modbus virtual port return an error.
If you need to change Modbus port params or options, you can always create new Modbus virtual port with the same ID, without deleting the previous one. Port configuration and options will be overwritten.
Testing Modbus virtual port
To test defined Modbus virtual port, execute the following command:
eva uc modbus test <ID> # e.g. eva uc modbus test p1
The command connects UC to Modbus port and checks the operation status.
As Modbus UDP doesn’t require a port to be connected, test command always return “OK” result.
Deleting Modbus virtual port
To delete Modbus virtual port, execute the command:
eva uc modbus destroy <ID> # e.g. eva uc modbus destroy p1
Note that controller doesn’t check if the port is in use or not, so double check this manually before deleting it.
Universal Controller can work as Modbus slave. Ports, the slave listens to, are set in etc/uc.ini. Modbus over TCP, UDP and serial ports (rtu/ascii/binary) is supported.
Controller uses single memory space for all ports it listens to, ports can have different Modbus addresses. Memory space has 10 000 holding registers, 10 000 coils, 10 000 input registers and 10 000 discrete inputs.
Units can listen to memory space changes and automatically update their status and value as soon as Modbus register is being changed. To activate state updates via Modbus slave memory space, set unit modbus_status and/or modbus_value properties to the corresponding registers, using before the number c for coil and h for holding register, e.g. c5 for 5th coil register, h50 for 50th holding register etc.
As Modbus values can be only integers, you may specify divider (or multiplier as well). To convert unsigned integer to signed, specify “S” before address. E.g. you have Modbus temperature sensor which stores its value every X seconds to holding register 5 on Universal Controller, multiplied by 100 and as signed integer. To automatically convert this value, set modbus_value = hS5/100
Sensors can update their value only. Don’t forget to enable sensor (set its status to 1) manually.
More complex data processing can be performed via PHI modules.